Netgear Netgear Nighthawk R8000P
- The Netgear Nighthawk R8000P is a high-performance router that provides fast and reliable connectivity for your home or office network.
Specifications
- CPU
- 1.8 GHz quad-core
- LAN
- Gigabit Ethernet
- QoS
- Yes
- RAM
- 512 MB
- USB
- 1x USB 3.0, 1x USB 2.0
- WAN
- Gigabit Ethernet
- Wi-Fi
- 802.11a/b/g/n/ac
- Bands
- Tri-band
- Flash
- 128 MB
- Ports
- 1x WAN, 4x LAN, 2x USB
- Antenna
- External
- MU-MIMO
- Yes
- Antennas
- 6
- LAN Ports
- 4x GE
- WAN Ports
- 1x GE
Potential Threats
10 Known CVEs
Default IP
192.168.1.1
Default admin panel address for Netgear Netgear Nighthawk R8000P
Default Credentials — Netgear Netgear Nighthawk R8000P
Known CVE Vulnerabilities (10)
An HTTP request smuggling attack in TP-Link AX10v1 before v1_211117 allows a remote unauthenticated attacker to DoS the web application via sending a...
This vulnerability allows network-adjacent attackers to execute arbitrary code on affected installations of NETGEAR Orbi 2.5.1.16 routers. Authenticat...
NETGEAR JGS516PE devices before 2.6.0.43 are affected by lack of access control at the function level.
This vulnerability allows network-adjacent attackers to bypass authentication on affected installations of NETGEAR R6700 V1.0.4.84_10.0.58 routers. Au...
Certain NETGEAR devices allow unauthenticated access to critical .cgi and .htm pages via a substring ending with .jpg, such as by appending ?x=1.jpg t...
Certain NETGEAR devices allow remote attackers to disable all authentication requirements by visiting genieDisableLanChanged.cgi. The attacker can the...
gif2png 2.5.13 has a memory leak in the writefile function.
OTCMS v3.85 allows arbitrary PHP Code Execution because admin/sysCheckFile_deal.php blocks "into outfile" in a SELECT statement, but does not block th...
OTCMS v3.85 has CSRF in the admin/member_deal.php Admin Panel page, leading to creation of a new management group account, as demonstrated by superadm...
S-CMS v1.5 has XSS in tpl.php via the member/member_login.php from parameter.
FAQ
The most common default credentials for Netgear Netgear Nighthawk R8000P are listed in the table above. Always change these immediately after setup.
The default username for Netgear Netgear Nighthawk R8000P is typically "admin". The full list of default credentials including username, password, access type and port is shown in the table on this page.
Log in to the admin panel using the default credentials listed above. Navigate to Administration → Password or System → Account settings. Enter the current password and set a new strong password. Save the changes.
Locate the Reset button (usually a small pinhole on the back/bottom of the device). Hold it for 10-30 seconds while powered on until the LEDs flash. The device will reboot with default settings.
No. Default credentials are publicly known and frequently exploited by automated scanners. Change the admin password immediately after first login.
The default admin login address for Netgear Netgear Nighthawk R8000P is shown in the "Default IP" field above. Most routers use 192.168.1.1 or 192.168.0.1. Open a browser on a device connected to the router and navigate to that IP.
Log in to the router admin panel at the default IP address. Go to Wireless or Wi-Fi settings. Find the WPA2/WPA3 passphrase field and update it. Save and reconnect your devices.
Change the default admin password and Wi-Fi password immediately. Disable WPS (Wi-Fi Protected Setup) — it is vulnerable to brute-force attacks. Enable WPA3 encryption if supported. Turn off remote management unless needed. Keep firmware updated.
Netgear Netgear Nighthawk R8000P has 10 known CVE vulnerabilities documented in our database. The full list with severity ratings is shown on this page. Apply the latest firmware update from the manufacturer to address known issues.
