Juniper Networks Juniper MX104
- The Juniper Networks Juniper MX104 is a high-performance, multi-service router designed for service provider and enterprise networks.
Specifications
- OS
- Junos OS
- QoS
- Yes
- USB
- Yes
- VPN
- Yes
- DIN Rail
- AC/DC
- Layer
- Layer 3
- Ports
- 4x MIC slots, 4x built-in 10GbE SFP+, 4x built-in GbE RJ-45
- Storage
- SSD
- Firewall
- Yes
- WAN Ports
- 8x
- Management
- Console, AUX, USB
- Operating Temp
- 0 to 45°C
Potential Threats
22 Known CVEs
Default IP
192.168.1.1
Default admin panel address for Juniper Networks Juniper MX104
Default Credentials — Juniper Networks Juniper MX104
| Username | Password | Access Type | Protocol | Port | Notes |
|---|---|---|---|---|---|
| (blank) | console | Console | — | ||
| (blank) | ssh | SSH | 22 |
Known CVE Vulnerabilities (22)
An Authentication Bypass Using an Alternate Path or Channel vulnerability in Juniper Networks Session Smart Router may allows a network-based attacker...
Vulnerability in the Oracle Java SE, Oracle GraalVM for JDK, Oracle GraalVM Enterprise Edition product of Oracle Java SE (component: JSSE). Supported...
Vulnerability in the MySQL Server product of Oracle MySQL (component: Server: Optimizer). Supported versions that are affected are 8.0.0-8.0.41, 8.4....
Vulnerability in the MySQL Server product of Oracle MySQL (component: Server: DDL). Supported versions that are affected are 8.0.0-8.0.41, 8.4.0-8.4....
Vulnerability in Oracle Secure Backup (component: General). Supported versions that are affected are 12.1.0.1, 12.1.0.2, 12.1.0.3, 18.1.0.0, 18.1.0.1...
A vulnerability has been identified in Industrial Edge Device Kit - arm64 V1.17 (All versions), Industrial Edge Device Kit - arm64 V1.18 (All versions...
An Improper Isolation or Compartmentalization vulnerability in the kernel of Juniper Networks Junos OS allows a local attacker with high privileges to...
A vulnerability has been identified in APOGEE PXC Series (BACnet) (All versions), APOGEE PXC Series (P2 Ethernet) (All versions), TALON TC Series (BAC...
A vulnerability has been identified in APOGEE PXC Series (BACnet) (All versions), APOGEE PXC Series (P2 Ethernet) (All versions), TALON TC Series (BAC...
Vulnerability in the MySQL Server product of Oracle MySQL (component: Server: Optimizer). Supported versions that are affected are 9.1.0 and prior. E...
Showing 10 of 22
FAQ
The most common default credentials for Juniper Networks Juniper MX104 are listed in the table above. Always change these immediately after setup.
The default username for Juniper Networks Juniper MX104 is typically "admin". The full list of default credentials including username, password, access type and port is shown in the table on this page.
Log in to the admin panel using the default credentials listed above. Navigate to Administration → Password or System → Account settings. Enter the current password and set a new strong password. Save the changes.
Locate the Reset button (usually a small pinhole on the back/bottom of the device). Hold it for 10-30 seconds while powered on until the LEDs flash. The device will reboot with default settings.
No. Default credentials are publicly known and frequently exploited by automated scanners. Change the admin password immediately after first login.
The default admin login address for Juniper Networks Juniper MX104 is shown in the "Default IP" field above. Most routers use 192.168.1.1 or 192.168.0.1. Open a browser on a device connected to the router and navigate to that IP.
Log in to the router admin panel at the default IP address. Go to Wireless or Wi-Fi settings. Find the WPA2/WPA3 passphrase field and update it. Save and reconnect your devices.
Change the default admin password and Wi-Fi password immediately. Disable WPS (Wi-Fi Protected Setup) — it is vulnerable to brute-force attacks. Enable WPA3 encryption if supported. Turn off remote management unless needed. Keep firmware updated.
Juniper Networks Juniper MX104 has 22 known CVE vulnerabilities documented in our database. The full list with severity ratings is shown on this page. Apply the latest firmware update from the manufacturer to address known issues.
